Zirconia Veneer — Lab-Direct Monolithic Restoration
Monolithic zirconia veneer produced in our Shenzhen and Huizhou facilities. CAD/CAM milled from medical-grade zirconia blank, sintered, finished, and inspected under one workflow. Five to seven working days from approved design to dispatch. ISO 13485 certified facility.
Zirconia Veneer Specifications
| Parameter | Specification |
| Material | Yttria-stabilized zirconia (3Y-TZP / 4Y-PSZ / 5Y-PSZ selectable) |
| Fabrication | Monolithic — milled from a single zirconia blank, no porcelain layering |
| Indications | Anterior single-unit veneers, limited to case-appropriate indications |
| Minimum thickness | 0.5 mm (lab recommends 0.7–1.5 mm for clinical longevity) |
| Connector cross-section | ≥ 3 mm² (multi-unit cases only — veneer restoration is single-unit) |
| Cementation | Resin cement with 10-MDP primer; airborne-particle abrasion (50 µm Al₂O₃) at the intaglio |
| Shade systems | VITA Classical, VITA 3D-Master, custom shade matching on request |
| Finish | Glazed or polished — state preference on the RX form |
| Imaging files accepted | STL, PLY, OBJ from intraoral or model scanners |
Monolithic vs. Layered Zirconia Veneers
We produce both monolithic and layered restorations. For veneer indications, monolithic is the lab default unless the case requires layered optical characterization.
| Material construction | Single zirconia blank | Zirconia core + hand-layered porcelain |
| Lab working time | 3–4 hours | 5–6 hours |
| Chipping risk | Not applicable | Layer-interface dependent |
| Translucency | 5Y-PSZ (high); 4Y-PSZ (mid); 3Y-TZP (low) | Higher, technician-dependent |
| Recommended for | Posterior and most anterior single-unit veneer cases | High-aesthetic anterior cases where layered characterization is requested |
Layered zirconia veneer cases follow a different workflow and timeline. Specify “layered” on the RX form for any case where layered construction is required.
Indications and Contraindications
Appropriate for:
- Anterior single-unit veneer restorations
- Patients with sufficient enamel substrate for adhesive cementation
- Cases where preparation depth accommodates 0.7–1.5 mm reduction
- Cases within the shade and translucency range offered by the selected zirconia generation
Not appropriate for:
- Thin or zero-preparation veneer indications — see preparation depth guidance below
- Cases where the patient presents with parafunctional load exceeding the restorative design limits
- Veneers on metal frameworks, post-and-core buildups, or implant abutments alongside zenith-different materials
- Situations where adhesive cementation is contraindicated by the clinical substrate
Preparation Depth
Minimum preparation depth depends on the chosen zirconia generation:
- 3Y-TZP (high strength, lower translucency): 0.5–0.7 mm
- 4Y-PSZ (balanced): 0.7–1.0 mm
- 5Y-PSZ (high translucency, lower strength): 1.0–1.5 mm
We do not recommend fabrication of zirconia veneers at minimum submillimeter thickness where adhesive substrate is limited. Cases below the lab minimum are reduced without indication rather than fabricated to a thickness below clinical guidance.
Cementation Protocol
The veneer is supplied unprimed. Cementation is performed at the chairside:
- Airborne-particle abrasion of the intaglio surface with 50 µm alumina, then ultrasonic clean
- 10-MDP primer application (e.g., Clearfil Ceramic Primer, Monobond Plus, or equivalent)
- Dual-cure or light-cure resin cement placement, following the manufacturer’s working time
- Tack-cure, remove excess, full cure
Substrate matters. Adhesive cementation on enamel provides the highest long-term retention; cementation on zirconia or metal frameworks is not within the scope of this product.
Our Zirconia Veneer Manufacturing Process
All production stages are performed inside ASD’s Shenzhen and Huizhou facilities. No production step is outsourced to a third-party laboratory.
- Case intake and data verification
- CAD design (3Shape / DentalCAD)
- Model or intraoral scan print (if model required)
- CAM milling from pre-shaded zirconia blank
- Sintering per the blank manufacturer’s cycle
- Glazing or polishing, per RX specification
- Quality inspection (margins, contacts, occlusion, shade verification)
- Packaging in a protective case with lot-traceable CoA on request
- Dispatch via tracked courier (DHL, FedEx, UPS)
Capacity: Normal season — 8,000 zirconia single units and 2,000 zirconia bridge cases per month. Peak season — 15,000 single units and 3,000 bridge cases per month.
Standards and Documentation
| Standard / Regulation | Scope | Documentation |
| ISO 13485 | Quality management system for medical devices | Certificate on request |
| EU MDR Annex XIII | Custom-made dental device notification | Statement on file |
| FDA Establishment Registration | U.S. distribution | Listed in FDA database |
| UDI (2027 compliance) | Unique Device Identification | Per-case label from archive |
Lot-traceable Certificates of Analysis (CoA) are available on request for any individual case.
Turnaround
| Case type | Working days from approved design |
| Single-unit monolithic veneer | 5 working days |
| Multi-unit monolithic veneer case | 7 working days |
| Layered veneer case | 7 working days |
| Rush case | 3 working days (surcharge applies) |
Working days exclude weekends and Chinese public holidays. Design approval turnaround depends on case complexity and clinician response.
Warranty and Remake
- Free remake for any restoration that fails to seat on a case-appropriate tooth preparation
- Free remake for any restoration that fails due to lab-side defect within 60 months of dispatch
- Remake requests must include the original restoration, the RX form, and a written description of the failure mode
The lab does not warrant restorations seated outside the preparation or cementation guidelines above.
Submit a Case
To request a quote or submit a case:
- Download the RX form and complete the case details (preparation, shade, cementation preference)
- Upload intraoral or model scan in STL, PLY, or OBJ format
- Email the case to the address below, or use the online submission form
For questions on case selection, material generation, or preparation design, contact the lab directly.
- Email: [email protected]
- Online submission: Case Submission Form
- Facility tour: Schedule a Video Factory Tour
Serving 50+ dental lab partners, 100+ dental practices, and 400+ dentists across the United States and Europe.














